How to Set Up a TP-Link DSL Modem Router via the Web Management Page (Classic Interface)

When You Set Up
更新November 18, 2026

This guide shows you how to set up a TP-Link DSL modem router via the Web Management Page, whether your internet service arrives through a DSL phone line or an Ethernet cable. (Applicable Models: Archer VR400 V1 V2 V3, Archer VR2100, Archer VR300, etc.)

If your router model is Archer VR400 V4 or Archer VX1800v, refer to this guide instead:

How to Set Up a TP-Link DSL Modem Router via the Web Management Page (New Interface)

If you prefer to set up the router using the Tether app, refer to this guide instead:

How to Set Up a TP-Link DSL Modem Router Using the Tether App (Classic Interface)

Key Takeaways

  • Connect to the router’s Wi-Fi or a LAN port before opening tplinkmodem.net; internet access is not required for local setup.
  • Use DSL Modem Router Mode for a DSL phone line or Wireless Router Mode for an Ethernet internet connection.
  • Identify your cable type, then follow the corresponding setup section (DSL or Wireless Router mode).
  • Enter your ISP’s connection type and any required PPPoE credentials, VLAN ID, or DSL type (VDSL or ADSL).
  • Save your settings, reconnect to Wi-Fi if needed, and open a website to confirm internet access.

Before You Begin

1. Check the model and hardware version on the router’s label.

2. Identify Your Internet Cable and Determine the Correct Operation Mode

A DSL modem router combines a DSL modem and a Wi-Fi router. Choose its operation mode based on the cable that brings internet service into the router:

  • DSL phone cable (RJ11): Connect it to the smaller port labeled DSL. Use DSL Modem Router Mode. If your ISP requires a splitter or filter, connect it as instructed by your ISP.
  • Ethernet cable (RJ45): Connect it to the larger port labeled LAN4/WAN. Use Wireless Router Mode. Connect the other end to your existing modem, fiber terminal/ONT, main router, or internet-enabled wall outlet.

For help identifying the connectors, see RJ11 vs. RJ45.

A smaller RJ11 DSL phone connector and a larger RJ45 Ethernet cable connector.

3. Gather Information from Your ISP.

Contact your Internet Service Provider (ISP) to obtain the following connection details:

1) Internet Connection Type:

  • Dynamic IP: Typically requires no credentials.
  • PPPoE: Requires a specific username and password provided by your ISP.
  • Static IP: Requires a fixed IP address, Subnet Mask, Gateway, and DNS servers.

2) VLAN ID: Required by certain ISPs.

3) DSL Modulation Type (if using DSL): VDSL or ADSL.

Step-by-Step Guide

Guide for Setting DSL Modem Router Mode

Step 1. Access the Web Management Page

Connect your phone or computer to the router via Wi-Fi or an Ethernet cable.

Open a web browser and enter https://tplinkmodem.net/ in the address bar.

Log in with your admin password. (For first login, you’ll be asked to create an admin password)

Step 2. Set the Region and Time Zone

After logging in, open Quick Setup if it does not start automatically. Select your Region and Time Zone, and click Next.

Web Quick Setup interface for selecting the region and time zone.

Step 3. Select Your ISP

Choose your provider from the ISP List dropdown. Select Other if your ISP is not listed, then click Next.

Web Quick Setup ISP list with Other selected.

Step 4. Enter Your Internet Settings

Enter the connection details provided by your ISP:

  • L2 Interface Type: Select VDSL or ADSL.
  • VLAN ID: Check Enable VLAN ID and enter the number if required by your provider.
  • Internet Connection Type: Choose PPPoE, Dynamic IP, or Static IP, and enter credentials if prompted.

Click Next.

Web internet setup page showing L2 interface choices, VLAN, and internet connection type.

Step 5. Set Your Wi-Fi Network Name and Password

Set the Wi-Fi name (SSID) and password. If you want the 2.4G & 5G Wi-Fi names and passwords to be the same, enable Smart Connect. If it is disabled, configure each band separately as needed. Click Next.

Web wireless settings page with smart connect and Wi-Fi name and password fields.

Step 6. Configure Firmware Auto Update (Applies Only to Certain Models)

Choose your preference and an update time, then click Next.

Web setup page offering automatic firmware updates and an update schedule.

Step 7. Complete Setup and Bind TP-Link ID

Note: If you changed the default Wi-Fi settings, please reconnect to the new Wi-Fi network, then return to the web interface. (You can skip this step if connected via Ethernet.)

Wait for the router to test the internet connection. Once successful, click Next. You can optionally log in with your TP-Link ID for remote cloud management, or click Log in Later to complete the setup.

If the test fails, double-check your cable connection, operation mode, and ISP credentials.

Web setup completion page with TP-Link ID login and Log in Later options.

Guide for Setting Wireless Router Mode

Step 1. Access the Web Management Page

Connect your phone or computer to the router via Wi-Fi or an Ethernet cable. (Do not connect the Ethernet cable to the LAN4/WAN port for now, to avoid being unable to log in to the web interface).

Open a web browser and enter https://tplinkmodem.net/ in the address bar.

Log in with your admin password. (For first login, you’ll be asked to create an admin password)

Step 2. Set the Region and Time Zone

After logging in, open Quick Setup. Select your Region and Time Zone, click Next.

Web Quick Setup interface for selecting the region and time zone.

Step 3. Select Wireless Router Mode

If the Quick Setup wizard asks for an operation mode, select Wireless Router Mode, click Yes if prompted, and wait for the router to restart. Reconnect to the router and log in again.

Web Quick Setup interface for choosing Wireless Router Mode.

If the wizard does not prompt you to select an operation mode, click Exit to leave Quick Setup. Then go to Advanced > Operation Mode, select Wireless Router Mode, click Save, and click Yes to reboot. Reconnect to the router and log in again.

Web Quick Setup interface for selecting the ISP.

Locate Advanced Operation Mode page with Wireless Router Mode selected and a restart confirmation.

Step 4. Configure the Internet Connection

Connect the Ethernet cable to the LAN4/WAN port.

Go to Advanced > Network > Internet. Click Add (or edit the existing connection profile) and configure the parameters according to your connection type:

  • VLAN ID: If required, check Enable and enter your VLAN ID.
  • Internet Connection Type: Select Dynamic IP, PPPoE, or Static IP.

Click Save.

Locate Advanced Ethernet internet configuration showing VLAN and internet connection.

Step 5. Configure Wireless Settings (Optional)

If you wish to change your Wi-Fi name and password, go to Basic > Wireless (or Advanced > Wireless > Wireless Settings) to customize your 2.4 GHz and 5 GHz networks, then click Save.

Web wireless settings page with smart connect and Wi-Fi name and password fields.

Step 6. Verify Internet Connectivity

Wait 3 to 5 minutes for the router to negotiate the connection with your ISP.

Check the physical Internet LED on the front panel:

  • Solid White / Green: Connected successfully to the Internet.
  • Orange / Off: No Internet connection. Double-check your cable connection, operation mode, and ISP credentials.

相關 FAQ

更多相關文章

這篇faq是否有用?

您的反饋將幫助我們改善網站

Community

TP-Link Community

Still need help? Search for answers, ask questions, and get help from TP-Link experts and other users around the world.

Visit the Community >